Installations- und Benutzerhandbücher als Download

5-Achsen-Messtechnik

• Broschüre: REVO-2 und RSP2 Messtaster
  

  Broschüre: REVO-2 und RSP2 Messtaster

  REVO-2 ist das einzige Scan-System für KMGs, das die Bewegung von drei Maschinenund zwei Messkopfachsen gleichzeitig steuert und dabei über 2D und 3D taktile Messtaster, Oberflächenrauheits-Messtaster und jetzt auch über berührungslose optische Messsensoren, Werkstückdaten erfasst.

  [358kB]
• Broschüre: RSP3-1 bis -4 Messtaster für REVO-2
  

  Broschüre: RSP3-1 bis -4 Messtaster für REVO-2

  Die RSP3 Messtaster werden für das 3-Achsen Scanning mit festen REVO-2 Kopfwinkeln während einer Messung verwendet. Die Taster sind so konzipiert, um eine optimierte Genauigkeit und Kontaktkraft für eine spezifische Tasterreihe zu bieten. Deshalb können die RSH3 Tasterhalter nur an ihrem entsprechenden RSP3 Messtaster angebracht werden.

  [267kB]
• Broschüre: RSP3-6 verlängerter Messtaster
  

  Broschüre: RSP3-6 verlängerter Messtaster

  Der RSP3-6 eignet sich besonders gut für den Zugang zu tiefen Bohrungen und die Prüfung von Merkmalen in großen Werkstücken. Er ist mit einer Reihe von Tasterhaltern für diverse Anwendungen erhältlich, die gerade und abgewinkelte Verlängerungen erfordern, und kann sowohl für berührend schaltende Messungen als auch zum 2D-Scannen eingesetzt werden.

  [425kB]
• Broschüre: RVP - optischer Messsensor für REVO-2
  

  Broschüre: RVP - optischer Messsensor für REVO-2

  RVP erweitert die Bandbreite der Anwendungen des REVO-2 Systems zusätzlich durch einen Sensor für die berührungslose Kantenerkennung, der mit allen anderen REVO Messtasteroptionen automatisch wechselbar ist. Dieses System bietet daher stets das optimale Werkzeug für die Messung vielfältiger Merkmale auf einer einzigen KMG Plattform und die Möglichkeit, eine größere Auswahl an Werkstücken zu prüfen.

  [527kB]
• Broschüre: SFP2 Rauheitsmesstaster
  

  Broschüre: SFP2 Rauheitsmesstaster

  Der SFP2 Messtaster erweitert die Multisensor-Funktion des REVO®-Systems dank der Rauheitsmessfähigkeit, die neben der schaltenden, Hochgeschwindigkeits-Scanning- und berührungslosen, optischen Messfähigkeit auf einem KMG zur Verfügung steht.

  [265kB]
• Datenblatt: SFM-A1
  

  Datenblatt: SFM-A1

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [176kB]
• Datenblatt: SFM-A2
  

  Datenblatt: SFM-A2

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [199kB]
• Datenblatt: SFM-B1
  

  Datenblatt: SFM-B1

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [165kB]
• Datenblatt: SFM-B2
  

  Datenblatt: SFM-B2

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [205kB]
• Datenblatt: SFM-B3
  

  Datenblatt: SFM-B3

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [166kB]
• Datenblatt: SFM-B4
  

  Datenblatt: SFM-B4

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [201kB]
• Datenblatt: SFM-B5
  

  Datenblatt: SFM-B5

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [191kB]
• Datenblatt: SFM-C3
  

  Datenblatt: SFM-C3

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [164kB]
• Datenblatt: SFM-D1
  

  Datenblatt: SFM-D1

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [165kB]
• Datenblatt: SFM-E1
  

  Datenblatt: SFM-E1

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [161kB]
• Datenblatt: SFM-E2
  

  Datenblatt: SFM-E2

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [164kB]
• Datenblatt: SFM-G1
  

  Datenblatt: SFM-G1

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [164kB]
• Datenblatt: SFM-H1
  

  Datenblatt: SFM-H1

  Erweiterter Zugang und Messkapazität für integrierte Rauheitsmessungen

  [171kB]
• Flyer: Calibration and capability artefacts for SFP2 surface finish probe [en]
  

  Flyer: Calibration and capability artefacts for SFP2 surface finish probe

  Surface finish measurement has traditionally involved the use of hand-held sensors or has required the part to be moved onto a costly dedicated measuring machine. The SFP2 probe for the REVO® 5-axis system changes all this, making surface finish inspection an integral part of CMM measurement, enabling the automatic switching between scanning, optical non-contact and surface finish measurement probe types.

  [606kB]
• Datenblatt: PH20 Schaltkopf-System
  

  Datenblatt: PH20 Schaltkopf-System

  PH20 ist ein dynamischer Schaltkopf welcher einen dreimal höheren Messdurchsatz bei gleichbleibend hoher Systemgenauigkeit ermöglicht.

  [937kB]

• Benutzerhandbuch: REVO-2
  

  Benutzerhandbuch: REVO-2

  No description available

  [2.6MB]
• Installation & user's guide: RSP3 (H-1000-5124) [en]
  

  Installation & user's guide: RSP3 (H-1000-5124)

  The RSP3 range of probes gives REVO users the ability to carry cranked stylus arrangements and enhanced capability for carrying long styli.

  [1.6MB]
• Installations- und Benutzerhandbücher: SFP2
  

  Installations- und Benutzerhandbücher: SFP2

  Das SFP2 Messsystem ermöglicht die Integration automatischer Rauheitsmessungen (Oberflächenrauheit) auf KMGs, die mit dem REVO Multisensor 5-Achsen-Messsystem bestückt sind.

  [1.4MB]
• User guide: RVP (H-1000-3322) [en]
  

  User guide: RVP (H-1000-3322)

  RVP is a non-contact vision measurement probe for use with the REVO-2 5-axis measurement system on co-ordinate measuring machines.

  [1.0MB]
• Installation & user's guide: RUP1 (H-1000-5396) [en]
  

  Installation & user's guide: RUP1 (H-1000-5396)

  The RUP1 probe system brings automated thickness measurement to CMMs as part of the REVO 5-axis multi-sensor measuring system.

  [1.6MB]
• Installation & user's guide: RTP1 (H-1000-5406) [en]
  

  Installation & user's guide: RTP1 (H-1000-5406)

  The REVO® temperature probe RTP1 allows the temperature of the part to be measured, recorded and used in logic. The innovative design provides excellent coupling between the probe and the material, enabling quick temperature measurement.

  [628kB]
• Installations- und Benutzerhandbücher: PH20
  

  Installations- und Benutzerhandbücher: PH20

  No description available

  [1.5MB]

3-Achsen-Messtechnik

• Broschüre: Übersicht über die motorischen PH10 PLUS Dreh-/Schwenkköpfe
  

  Broschüre: Übersicht über die motorischen PH10 PLUS Dreh-/Schwenkköpfe

  Die motorischen Dreh-/Schwenkköpfe der Reihe PH10 PLUS steigern den Messdurchsatz, denn sie erlauben CNC-gesteuerten KMGs die programmgesteuerte wiederholgenaue Messtasterpositionierung. Dadurch können Merkmale aus verschiedenen Winkeln gemessen werden, ohne dass eine häufige, zeitaufwendige Änderung der Tastereinsatzkonfigurationen erforderlich ist.

  [545kB]
• Flyer: PH10M-iQ PLUS [en]
  

  Flyer: PH10M-iQ PLUS

  PH10M-iQ PLUS – Less time calibrating, more time measuring

  [591kB]
• Data sheet: AM2 adjustment module (H-1000-2051) [en]
  

  Data sheet: AM2 adjustment module (H-1000-2051)

  The AM2 adjustment module is designed to provide quick and accurate angular alignment of the PH10MQ PLUS motorised probe head with the axes of the co-ordinate measuring machine and / or the autochange rack.

  [81kB]

• Installation & user's guide: PH10 PLUS (H-1000-7592) [en]
  

  Installation & user's guide: PH10 PLUS (H-1000-7592)

  Each of the heads in the PH10 PLUS motorised probe head range is a general purpose, versatile unit designed specifically for use on direct computer controlled (DCC) coordinate measuring machines (CMMs).

  [960kB]
• Installation & user's guide: PH10M-iQ PLUS (H-1000-7564) [en]
  

  Installation & user's guide: PH10M-iQ PLUS (H-1000-7564)

  PH10M-iQ PLUS is a derivitive of the PH10 PLUS range of heads. PH10M-iQ PLUS has inferred qualification meaning that after initial calibration is performed, all other positions of the head are inferred which eliminates the need to recalibrate each required head position.

  [872kB]
• Installation & user's guide: PHS-2 (H-1000-5620) [en]
  

  Installation & user's guide: PHS-2 (H-1000-5620)

  PHS-2 is designed to meet the arduous requirements of 'body-in-white' measurement, where fine angular position and long reach are needed.

  [3.2MB]

Manuelle Messköpfe

• User guide: PH6M [en]
  

  User guide: PH6M

  No description available

  [361kB]
• Benutzerhandbuch: Manueller Dreh-/Schwenkkopf MIH
  

  Benutzerhandbuch: Manueller Dreh-/Schwenkkopf MIH

  H-1000-5201-07-A

  [424kB]
• Benutzerhandbuch: MH8
  

  Benutzerhandbuch: MH8

  Der MH8 ist ein manuell indexierbarer Tastkopf mit Dreh‐ und Schwenkfähigkeit, um das Positionieren der Tasterkonfiguration zu ermöglichen. Der Kopf kann mit Messtastern verwendet werden, die mit einer Renishaw M8‐Aufnahme ausgestattet sind. Empfohlen werden die berührend schaltenden Messtaster TP20 bzw. TP6. Der MH8 ist, je nach der vom KMG‐Hersteller spezifizierten Montageart, mit verschiedenen Aufnahmeschäften lieferbar.

  [420kB]
• User guide: MH20 and MH20i (H-1000-5195) [en]
  

  User guide: MH20 and MH20i (H-1000-5195)

  The MH20 and MH20i are manually operated probe heads that articulate to provide orientation of the probing axis. MH20 provides nonrepeatable orientation, while MH20i permits repeatable indexing at 15° increments marked on the A and B axes. Both heads feature TP20 kinematic (magnetic) probe mounting, allowing stylus module changes without the need for re-qualification. A range of shanks is available to suit most CMM quills.

  [533kB]
• User guide: RTP20 [en]
  

  User guide: RTP20

  No description available

  [554kB]

Messtaster zum Scannen

• Flyer: SP80 ultra-high accuracy scanning probe [en]
  

  Flyer: SP80 ultra-high accuracy scanning probe

  The SP80 quill mounted probe provides class-leading scanning performance, as well as the most flexible use of styli for maximum productivity.

  [267kB]

• Installation guide: SP25M [en]
  

  Installation guide: SP25M

  This document is intended as a guide to initial installation and integration of the Renishaw SP25M analogue scanning/measurement probe system.

  [1.2MB]
• Installation guide: SP80 and SP80H [en]
  

  Installation guide: SP80 and SP80H

  This installation and integration guide is intended to assist OEM and Renishaw personnel in the initial installation, integration and use of the Renishaw SP80 and SP80H ultra-high accuracy scanning probes. The SP80 and SP80H are quadrature output measurement probes that provide class-leading performance, as well as the most flexible use of styli for maximum productivity.

  [1.2MB]
• Benutzerhandbuch: SP80 und SP80H höchstpräzise Messtastersysteme zum Scannen
  

  Benutzerhandbuch: SP80 und SP80H höchstpräzise Messtastersysteme zum Scannen

  No description available

  [3.0MB]
• Installation & user's guide: SP600, SCR600 and AC1, AC2 (H-1000-5175) [en]
  

  Installation & user's guide: SP600, SCR600 and AC1, AC2 (H-1000-5175)

  SP600M is an auto-jointed, multiwired analogue scanning probe suitable for mounting on certain motorised and fixed Renishaw probe heads. SP600Q is a quill mounted version of the SP600M analogue scanning probe. SP600 is a shank mounted version of the SP600M analogue scanning probe.

  [887kB]

Berührend (taktil) schaltende Messtaster

• Benutzerhandbuch: Schaltende Messtaster-Systeme - TP1, TP2, TP6, TPA, PH1, PH5, PH6, PH6M
  

  Benutzerhandbuch: Schaltende Messtaster-Systeme - TP1, TP2, TP6, TPA, PH1, PH5, PH6, PH6M

  No description available

  [514kB]
• Benutzerhandbuch: TP20
  

  Benutzerhandbuch: TP20

  No description available

  [970kB]
• Benutzerhandbuch: TP200 Messtastersystem
  

  Benutzerhandbuch: TP200 Messtastersystem

  H-1000-5014-03-C

  [310kB]
• User instructions: TP20 and TP200 cleaning [en]
  

  User instructions: TP20 and TP200 cleaning

  How to effectively clean the location faces of TP20 and TP200.

  [139kB]
• User guide: TP7 high accuracy touch trigger probe system [en]
  

  User guide: TP7 high accuracy touch trigger probe system

  No description available

  [480kB]
• Brochure: Stylus selection guide: TP7M probe and stylus kit [en]
  

  Brochure: Stylus selection guide: TP7M probe and stylus kit

  No description available

  [311kB]
• Brochure: Stylus selection guide: TP7M stylus kit [en]
  

  Brochure: Stylus selection guide: TP7M stylus kit

  No description available

  [125kB]
• Benutzerhandbuch: Manuell indexierbarer Messtaster TP8
  

  Benutzerhandbuch: Manuell indexierbarer Messtaster TP8

  No description available

  [129kB]
• Installation & user's guide: NDI AUTOsense touch-trigger module (H-1000-5180) [en]
  

  Installation & user's guide: NDI AUTOsense touch-trigger module (H-1000-5180)

  The AUTOsense module is a dual function stylus holder that enables touch trigger probing for both single-point and scanning. The AUTOsense module is only compatible with supported NDI hand-held probes.

  [1.3MB]

Messtaster-Interfaceeinheiten

• Installation guide: PI 7-3 [en]
  

  Installation guide: PI 7-3

  The PI 7-3 is a dedicated signal conditioner for interfacing the TP7M series of probes or touch-trigger probe types such as TP2, TP20 or TP6 / TP6A, to the CMM controller.

  [865kB]
• Installation guide: PI 200-3 [en]
  

  Installation guide: PI 200-3

  No description available

  [1.3MB]
• Installation guide: IS1-2 [en]
  

  Installation guide: IS1-2

  This guide describes how the IS1-2 (interface selector) functions when used with multiple Renishaw probing systems. It gives information on physical installation, system connections and interface settings, as well as assistance in fault finding during the installation of a system.

  [648kB]

Maschinensteuerungen und Verstärker

• Installation guide: PHC10-3 PLUS [en]
  

  Installation guide: PHC10-3 PLUS

  This guide gives information on physical installation, system connections, communications and interface settings, as well as assistance in fault-finding during the installation of PHC10-3 PLUS.

  [918kB]
• Installation guide: UCC T3 PLUS and UCC S3 CMM controller (H-1000-2118) [en]
  

  Installation guide: UCC T3 PLUS and UCC S3 CMM controller (H-1000-2118)

  No description available

  [1.5MB]
• Installation guide: UCC T3-2 (H-1000-5254) [en]
  

  Installation guide: UCC T3-2 (H-1000-5254)

  No description available

  [1.2MB]
• Installationshandbuch: UCC T5
  

  Installationshandbuch: UCC T5

  No description available

  [1.5MB]
• Installationshandbuch: UCC S5 REVO-2 KMG Steuerung Installationshandbuch (H-1000-5465)
  

  Installationshandbuch: UCC S5 REVO-2 KMG Steuerung Installationshandbuch (H-1000-5465)

  No description available

  [1.6MB]
• Installationshandbuch: UCC BI
  

  Installationshandbuch: UCC BI

  Die UCC BI wird für KMG Systeme benötigt, die mit bürstenlosen Motoren arbeiten. Die UCC BI ist die Schnittstelle zwischen der KMG Steuerung und dem SPA2‐2 ﴾der die bürstenlosen Motoren speist﴿.

  [1.2MB]
• Installation guide: UCC AI [en]
  

  Installation guide: UCC AI

  The UCC AI is required for large higher voltage CMM systems which may require motor voltages in excess of 80 V or motor currents in excess of 10 A.

  [917kB]
• Installation guide: UCC PI 80 [en]
  

  Installation guide: UCC PI 80

  The UCC PI 80 is required for CMM systems which are fitted with Renishaw's SP80 scanning probe and facilitates the use of the UCC S3 as the machine controller.

  [787kB]
• Installation guide: UCC daughtercards (H-1000-5220) [en]
  

  Installation guide: UCC daughtercards (H-1000-5220)

  There is a range of UCC daughtercards available each card offering additional capabilities to the standard UCC1 or UCC2 product.

  [1.5MB]
• Leaflet: UCC daughtercards [en]
  

  Leaflet: UCC daughtercards

  No description available

  [54kB]
• Installations- und Benutzerhandbücher: MCU
  

  Installations- und Benutzerhandbücher: MCU

  No description available

  [1.0MB]
• Leaflet: MCU docking plate [en]
  

  Leaflet: MCU docking plate

  No description available

  [113kB]
• Installation & user's guide: MCUlite-2, MCU5-2 and MCU W-2 (H-1000-5280) [en]
  

  Installation & user's guide: MCUlite-2, MCU5-2 and MCU W-2 (H-1000-5280)

  The MCUlite-2 is a basic entry level joystick . It has the controls necessary to control a 3-axis touch-trigger CMM and Renishaw head but without the sophistication of an LCD display screen. The MCU5-2 has been developed for use with Renishaw's REVO and PH20 systems, providing the ability to move the CMM in the probe and stylus axis and has an LCD display. The wireless manual control unit (MCU W-2) is a CMM joystick designed for use with Renishaw's range of UCC controllers. Based on the MCU5‐2 joystick design, the MCU W‐2 uses modern battery technology and Bluetooth® radio modules to provide an effective wireless joystick with a maximum range of 25 m and over eight hours between battery changes.

  [1.1MB]
• User guide: HCU2 [en]
  

  User guide: HCU2

  No description available

  [234kB]
• Installation guide: SPAlite (H-1000-5107) - legacy [en]
  

  Installation guide: SPAlite (H-1000-5107) - legacy

  The SPAlite is a servo power amplifier designed specifically for use with the Renishaw UCC2 and UCClite controllers. The SPAlite is capable of controlling three axes of movement with configurable velocity feedback options to match the requirements of your installation.

  [354kB]
• Installation guide: SPA2-2 (H-1000-5247) [en]
  

  Installation guide: SPA2-2 (H-1000-5247)

  SPA2-2 servo power amplifier installation guide

  [1.4MB]
• Installation guide: SPA3 (H-1000-7566) - legacy [en]
  

  Installation guide: SPA3 (H-1000-7566) - legacy

  SPA3 is a servo power amplifier with enhancements for higher power and category 2 E-STOP. The high power capability combined with a compact form enables use of the SPA3 across a wide range of machines.

  [1.6MB]
• Installation guide: SPA3-2 (H-1000-5364) [en]
  

  Installation guide: SPA3-2 (H-1000-5364)

  No description available

  [1.5MB]
• Manual: Digital servo power amplifiers [en]
  

  Manual: Digital servo power amplifiers

  A publication to assist in the task of setting up the servo response of the CMM when fitted with either an SPA2 or SPAlite servo power amplifier.

  [1.9MB]
• User guide: Product interconnection system (PICS) (H-1000-5000) [en]
  

  User guide: Product interconnection system (PICS) (H-1000-5000)

  No description available

  [557kB]

Magazine und Module

• Data sheet: TCR20 (H-1000-1371) [en]
  

  Data sheet: TCR20 (H-1000-1371)

  Based on the industry standard range of MCR20 rack systems, TCR20 securely stores modules for rapid automatic changing, protecting mating surfaces from any airborne contaminants within the working envelope of the machine.

  [417kB]

• User guide: Autochange system [en]
  

  User guide: Autochange system

  Renishaw’s ACR1 is a fully integrated 8 port probe exchange system. Mounted within the CMM’s working envelope, the autochange system facilitates fast, automatic probe exchange without the need for re-qualification of the probe assembly.

  [2.6MB]
• Installation guide: Autochange system [en]
  

  Installation guide: Autochange system

  Installation and programmer's guide for Renishaw's autochange system

  [3.5MB]
• Installation guide: ACR2 [en]
  

  Installation guide: ACR2

  No description available

  [1.1MB]
• Installations- und Benutzerhandbücher: ACR3
  

  Installations- und Benutzerhandbücher: ACR3

  No description available

  [1.2MB]
• Leaflet: ACR3 with powered port - power supply addendum [en]
  

  Leaflet: ACR3 with powered port - power supply addendum

  No description available

  [43kB]
• Leaflet: RCP repair kit [en]
  

  Leaflet: RCP repair kit

  No description available

  [309kB]
• Installations- und Benutzerhandbücher: MRS modulares Befestigungssystem
  

  Installations- und Benutzerhandbücher: MRS modulares Befestigungssystem

  MRS modulares Befestigungssystem

  [871kB]
• Leaflet: User's leaflet: MRS adjustable footplates [en]
  

  Leaflet: User's leaflet: MRS adjustable footplates

  The MRS rail can be placed at different heights from the CMM’s bed by using multiple MRS legs to provide the required clearance for long styli and extension bars. By using the optional MRS adjustable footplates shown below, the MRS rail can also be placed at different positions on the CMM’s bed thereby ensuring that a maximised working volume can be achieved.

  [111kB]
• Leaflet: User's leaflet: MRS heavy duty legs [en]
  

  Leaflet: User's leaflet: MRS heavy duty legs

  Where an MRS installation has numerous SCP80s containing heavy stylus arrangements, or vertical stylus arrangements exceeding 190 mm, it is recommended that the optional MRS heavy duty leg kits are used to provide additional rigidity/height. These kits can be purchased separately to match the number of legs used on the MRS.

  [211kB]
• Installation guide: MRS2 (H-1000-5255) [en]
  

  Installation guide: MRS2 (H-1000-5255)

  This guide provides detailed installation instructions for the Renishaw modular rack system (MRS2).

  [4.6MB]
• Installation guide: REVO-2 change system port spacing guide ( H-1000-5408) [en]
  

  Installation guide: REVO-2 change system port spacing guide ( H-1000-5408)

  No description available

  [4.2MB]

Zubehör

• User guide: AM1 [en]
  

  User guide: AM1

  The AM1 adjustment module has been designed for use with the PH6M and MIH manual probe heads and the PH10T/M PLUS motorised probe heads.

  [159kB]
• User guide: MCG [en]
  

  User guide: MCG

  Renishaw’s machine checking gauge (MCG) provides an easy way to monitor the volumetric measurement performance of your co-ordinate measuring machine (CMM). The MCG is an effective complement to existing standards for CMM verifi cation and can be used as an interim checking gauge in accordance with international standards BS EN ISO 10360-2.

  [538kB]
• User guide: MCG tools [en]
  

  User guide: MCG tools

  MCG tools is an Microsoft Excel workbook that manages the machine checking gauge (MCG). MCG tools allows the user to generate a DMIS part program in order to execute the MCG test on a co-ordinate measuring machine (CMM). It can then import the MCG data to analyze and identify whether geometrical errors exist on the CMM. Also, the results from every MCG test can be archived in order to follow the evolution of the geometry of a CMM over time.

  [822kB]
• Kurzanleitung: Messen der Antastkraft mit der Federwaage
  

  Kurzanleitung: Messen der Antastkraft mit der Federwaage

  No description available

  [46kB]
• Installation guide: Universal calibration tower assembly instructions (H-1000-5421) [en]
  

  Installation guide: Universal calibration tower assembly instructions (H-1000-5421)

  Universal calibration tower assembly instructions

  [1.9MB]

KMG Installationen

• Benutzerhandbuch: Nachrüst-Steuerungsschrank
  

  Benutzerhandbuch: Nachrüst-Steuerungsschrank

  Der Steuerungsschrank von Renishaw ist eine Standard 19”-Rack-Einheit, in der verschiedene Renishaw Steuerungen, Servoverstärker und Interfaces untergebracht werden können. Dieser Schrank bietet sowohl ein Lagersystem als auch ein einzigartiges Verbindungssystem hin zum KMG, wodurch eine saubere und ordentliche Installation möglich wird. Neben der Unterbringungsmöglichkeit für alle Renishaw-Geräte besitzt der Schrank ein integriertes Netzsystem mit Ein/Aus-Schalter.

  [528kB]
• Installation guide: Retrofit desk assembly instructions (H-1000-0019) [en]
  

  Installation guide: Retrofit desk assembly instructions (H-1000-0019)

  Assembly instructions for cabinet mounted and stand alone retrofit desk

  [1.8MB]
• Manual: Switch and connector guide: Renishaw CMM products [en]
  

  Manual: Switch and connector guide: Renishaw CMM products

  This guide contains information on switches, connectors and signals of conventional Renishaw interfaces and controllers. It is of particular use to engineers involved in installation, support or upgrade activities associated with Renishaw CMM products.

  [1.4MB]
• Manual: Reference guide: CMM cables [en]
  

  Manual: Reference guide: CMM cables

  This guide contains comprehensive information on the most commonly used Renishaw cables. It is of particular use to engineers involved in installation or support of Renishaw equipment on CMMs, or where correct cable identification is required.

  [2.2MB]
• Leaflet: Upgrade brackets and blanking plates [en]
  

  Leaflet: Upgrade brackets and blanking plates

  This leaflet details the bracket options available when upgrading or replacing Renishaw controllers and / or probe interfaces. By using a combination of the following brackets and / or blanking panels, any combination of existing and new Renishaw product can be mounted together inside a 19 inch cabinet rack. The bracket kits shown in this leaflet are supplied with all the necessary fixtures.

  [147kB]